Teac UH-7000 User Manual download pdf (Page 17)

TASCAM UH-7000

5 – Mixer Panel Settings

MIXER page

Use the MIXER page to make settings for the built-in mixer and

output signals.

The contents of this screen depend on the Mixer Mode setting

on the INTERFACE page.

NOTE

All settings except for the status of the SOLO buttons made

on the MIXER page are retained even when the unit is turned

off. The solo buttons are reset to their default values (off)

whenever the unit is turned off.

1 MON MIX slider

If the Mixer Mode setting on the INTERFACE page is set to

Multitrack, you can use the slider to adjust the balance of

the signal output from the built-in mixer.

Slide it all the way to the Input side to output only the

signals input to this unit, or slide it all the way to the

Computer side to output only the signals output from the

computer to the unit by USB.

Click the slider and drag it left and right to adjust it.

If the Mixer Mode setting on the INTERFACE page is set to

Stereo Mix, the MON MIX slider will not appear. The signals

input through each input jack and from the computer

output will be mixed and output from the unit.

NOTE

If the Mixer Mode setting is set to Multitrack, you can return

the MON MIX slider to the center position by clicking it while

pressing the following key on the computer keyboard.

Windows PC: ctrl key

Mac: command key

2 Status display area

This shows the current status of the unit.

Sample Rate: Current sampling frequency

Sample Width: Quantization bit depth

Digital Input Status: Shows the digital input status

Mixer Mode: Shows the mixer mode

3 Dynamics effects buttons

Click a dynamics effect button to select and use it.

No more than two types of dynamics effects can be used at

a time. (The one exception is the combination of the limiter

and low-cut filter effects.)

Options

Off (default): Effect name unlit

On: Effect name lit

To change the dynamics effect being used, click the

button of the desired effect. The previously used effect will

automatically be turned off, and the newly selected effect

will be turned on.

NOTE

•

Selection will not be possible when an effect cannot be used

because of sampling frequency conditions.

•

Turning the dynamics effect on/off using these buttons is

linked to the dynamics effect on/off setting on the EFFECT

page.

•

When the sampling frequency is 44.1 kHz or 48 kHz, both

the limiter and low-cut filter functions can be used together

at the same time. When using these two effects at the

same time, the send effect cannot be used. (See “Dynamics

effects” on page 20.)

4 Dynamics effects assignment buttons

Click the buttons for each channel and the MASTER L/R

button to assign the dynamics effect to it.

You cannot assign the dynamics effect to more than one

channel at a time.

Options

Off (default): Channel name button unlit

On: Assigned channel name button lit

To change the channel to which the dynamics effect is

assigned, click the channel name button of the desired

channel. The previously assigned channel name button will

become unlit, and the newly assigned channel name button

will light.

5 Analog input switches

Select the analog inputs for the Analog 1 and Analog 2

channels.

The button for the selected input lights.

LINE button: Input from the ANALOG (BALANCED) LINE IN

1/2 jacks.

MIC button: Input from the ANALOG (BALANCED) MIC IN

1/2 jacks.

6 Effects send selection buttons

Set whether the signal sent to the send bus is pre-fader or

post-fader.

The selected button lights.

Pre button: The signal is sent to the send bus before

adjustment by the channel fader. The send level will not

be affected by the channel fader.

Post button: The signal is sent to the send bus after

adjustment by the channel fader. The send level will be

affected by the channel fader.

NOTE

If neither the pre button nor the post button is selected, no

signal will be sent to the send bus.

7 Send knob

Use to adjust the level of the signal sent to the send bus

(send level).

Range: 0–127 (default: 0)

Use the mouse to click and drag a SEND knob up or down to

adjust the level.

While dragging the mouse, the value being adjusted is

shown beneath its SEND knob.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 35 36

Comments to this Manuals

No comments

Teac UH-7000 User Manual Page 17

Comments to this Manuals

Related products and manuals for Audio Teac UH-7000